General ⇒ Figure Scales

[rainz]

I hope this is the attachment you need

[cgnieder]

Yes, that's the one (I don't know why I confused sty and cls -- must be the heat).

However, I don't see any problems when I compile your code (with a replaced image). Every figure has the same height and width... (see attachment)

[rainz]

Sorry I am unable to find it. Thanks for the help anyway.

[rainz]

Do you know any website I can find a solution?

[rainz]

Does the below code work ok when you compile too?

Code: Select all

begin{table}[ht]
        \centering
                \begin{tabular}{l|l|l}
                \hline
Variable & VIF & 1/VIF \\ \hline
CI & 1.42 & 0.705277\\ 
GM & 1.30 & 0.767683 \\ 
ln(PV) & 1.17 & 0.855562\\ \hline
\textbf{Mean VIF }& \textbf{1.30}\\
\hline
\end{tabular}
\caption{Test for multicollinearity for model 4}
\label{mullcon 4}
\end{table}
\\
\begin{figure}
\centering
\scalebox{0.40}
        {\includegraphics{C:/histogram of residuals for model 4.png}}
\caption{Histogram of residuals for model 4}
\label{fig:histogram of residuals for model 4}
\end{figure}
\\
\begin{table}[ht]
        \centering
                \begin{tabular}{l|l|l|l|l|l}
                \hline
Variable & Obs & W & V & z & Prob $>$ z \\ \hline
Residuals & 126 & 0.99308 & 0.694 & -0.821 & 0.79409\\
\hline
\end{tabular}
\caption{Shapiro-Wilk W test for normal data for model 4}
\label{SW 4}
\end{table}
\\
\begin{figure}
\scalebox{0.40}
        {\includegraphics{C:/rvfplot for model 4.png}}
\caption{Residuals against fitted values for model 4}
\label{fig:Residuals against fitted values for model 4}
\end{figure}
\\

[Stefan Kottwitz]

You are at the right website.

I'm sure, the problem can be solved, if the information would be sufficient. For example, if you would post a small example with two such images as attachments which shows the effect when compiled. Having a test case leads usually to a solution.

Without further information, I just think you could use a fixed value for all pictures, such as

Code: Select all

\includegraphics[width=8cm]{name}

Stefan

[cgnieder]

On every other site they're going to ask you the same questions as I did. What you could do (and as I have suggested two times before) is attaching your images. They seem to be the source (provided your MWE still shows the undesired behaviour).

If I insert the code into the MWE, remove all the \\ (they're unnecessary and even raise errors) and replace the images with dummy ones,, then yes.

Regards

[Stefan Kottwitz]

Code: Select all

\scalebox{0.40}
        {\includegraphics{C:/histogram of residuals for model 4.png}}

Spaces in file names can be a problem. If the image won't be displayed, load grffile or rename it.

Instead of \scalebox, you could use \resizebox to get a fixed width or height.

Stefan

[rainz]

2 images are attached they have the same dormat as I previously mentioned but different sizes. Also, the name of the file is displayed near the image. How can I remove that?

Thanks guys for helping. Sorry for any trouble you have been through.

[Stefan Kottwitz]

the name of the file is displayed near the image. How can I remove that?

That's because of the spaces in the file name. As I suggested before, load grffile or rename it.

Stefan